At a glance
- Workplace
- Onsite
- Location
- Seattle
- Salary
- USD 110,000-170,000 / year
About the role
- Shield AI is seeking an RF and Microwave Hardware Design Engineer to design and deliver compact, high-performance RF modules for airborne and ground systems.
- The position focuses on hands-on module design rather than top-level communications architecture, waveform development, or link-budget ownership.
Responsibilities
- Design RF and microwave modules from requirements and architecture through schematic capture, component selection, layout, bring-up, verification, qualification, and production release, with scope and independence appropriate to level.
- Design active and passive RF circuits such as low-noise amplifiers, power amplifiers, filters and multiplexers, RF switches, limiters, couplers, attenuators, power detectors, and frequency-conversion stages.
- Develop RF front-end assemblies that meet gain, noise figure, output power, linearity, compression, efficiency, harmonic and spurious-emission, stability, isolation, and out-of-band rejection requirements.
- Perform circuit and electromagnetic analysis using tools such as Keysight ADS, Cadence AWR, HFSS, or CST, and correlate models with measured hardware performance.
- Create and review RF and mixed-signal PCB designs, including controlled-impedance routing, grounding, shielding, stack-up definition, power distribution, and placement of sensitive or high-power components.
- Plan and execute laboratory characterization using network analyzers, spectrum analyzers, signal generators, noise-figure analyzers, power meters, oscilloscopes, and automated test equipment.
- Diagnose difficult hardware issues involving instability, oscillation, intermodulation, self-interference, desense, thermal drift, mismatch, leakage, and electromagnetic coupling.
- Work closely with mechanical, thermal, avionics, communications, antenna, manufacturing, and test engineers to integrate RF hardware into size-, weight-, power-, cooling-, and environmental constraints.
- Develop verification methods, production test strategies, calibration approaches, and clear technical documentation that make designs repeatable and manufacturable.
- Support environmental and electromagnetic qualification, supplier engagements, hardware integration, ground test, and flight test as needed.
Requirements
- Bachelor's degree in Electrical Engineering, Applied Physics, or a related field, or equivalent practical experience.
- Typically 1 or more years of relevant post-undergraduate experience for L2, or 2 or more years for L3.
- Hands-on experience designing, building, or debugging an RF or microwave circuit, module, or PCB assembly through measured verification.
- Solid understanding of S-parameters, impedance matching, transmission lines, stability, gain and noise figure, linearity and compression, nonlinear products, isolation, and cascaded RF performance.
- Experience creating or reviewing RF PCB layouts with controlled impedance, grounding, shielding, component placement, and signal-integrity considerations.
- Proficiency with common RF laboratory instruments and calibration methods, with the ability to distinguish hardware behavior from measurement artifacts.
- Ability to use simulation and measured data to make sound design decisions, document tradeoffs, and close requirements with objective evidence.
- Clear written and verbal communication skills and the ability to work effectively with cross-functional engineering and manufacturing teams.
- Ability to work on-site in a laboratory and hardware-development environment.
Preferred qualifications
- Experience with RF front ends for airborne, defense, space, robotics, or other high-reliability systems.
- Experience integrating GaN or GaAs power amplifiers, MMICs, LNAs, switches, limiters, frequency converters, or high-selectivity filter technologies.
- Experience designing for simultaneous transmit and receive operation, high-power RF, intermodulation control, adjacent-band rejection, or co-site interference and desense.
- Experience with Altium Designer and one or more RF or electromagnetic simulation environments such as ADS, AWR, HFSS, or CST.
- Working knowledge of thermal design, RF packaging, connector and cable interfaces, tolerance analysis, and design for manufacturability and test.
- Experience with EMI and EMC design and qualification for military or aerospace hardware.
- Experience developing automated characterization or data-analysis tools in Python, MATLAB, or a similar environment.
- Experience transitioning RF hardware from prototype through qualification and low-rate production.
Benefits
- Bonus
- Benefits
- Equity
- Temporary benefits package (applicable after 60 days of employment for temporary employees)
Skills
- Keysight ADS
- Cadence AWR
- HFSS
- CST
- Altium Designer
- Python
- MATLAB
